SINCHOLD D2 Discontinuous Steel Composite Rail Rubber Pads
Product Introduction
SINCHOLD D2 Discontinuous Steel Composite Rail Rubber Pads are designed for installations where rails are mounted on individual sole plates.The rectangular groove of elastic composite rubber pad arranged in the section direction of the direction of the plate.To reduce the overall plate lateral force after deformation and the deformation caused by squeezing rubber surface damage.Because of the steel plate, the structure is very reasonable.After 2 million times of fatigue test is still a good performance. So, even after long time use plate is not damaged.
Product Feature and Application
The composite plate used for bedding under the rail and length along the rail layout. Width is smaller than rail bottom width 4 to 5 mm.The composite plate type structure become two layers of rubber block 0.5-0.7 high quality steel after hot glue composite structure type. Suitable temperature range -20℃-80℃.After the installation after the pressing force of rail plate, the composite plate can keep close contact with rail and rail bottom, make up the rail support surface roughness, in the loaded plate under wheel load will not stretch,instead the grooves are filled,enhance composite plate stiffness, can also prevent the large pressure produced by internal stress of crane, uniform crane wheel pressure, eliminate the fatigue stress produced by the concentrated load.
1.Rubber pads use oil resistant rubber,the performance should conform to GB/T5574-1994 standard 《industrial rubber》
Rubber pads machinery to meet the following requirements:
NameHardness
（Shore A ）Tensile Strength
N/mm²Elongation at Break(%)Pressured Elastic Modulus N/mm²
Composite Rubber PadH7—H8>13>25080~120
2.The bond stress between steel and rubber of composite rubber pad >1 N/mm²
3.Shore Hardness:75°±A 5(DIN53505)
4.Tensile Strength:（ASTMD412C）leave factory 12.5N/mm²^2—aging 10.5N/mm^2
5.Elongation: leave factory 250%—aging 200%
6.Long Deformation（According to BS903 part A6）leave factory less than 5%，aging less than 20%
7.Allowable Compression Stress：80N/mm^2=80MPa
8.Operating Temperature: from -25℃ to100℃
9.Noise and Vibration Reduction:Noise average reduction 10% DBA,vibration average reduction 48%an
Production Details
Deliver,Shipping and Service
Packaging Details:cartons or pallets
Delivery Detail: according to your requirements,accept L/C or T/T payment
If you're going to wholesale the sinchold d2 discontinuous steel composite rail rubber pads made in China, welcome to consult the price list and the quotation with us. We're one of the leading China manufacturers and suppliers, welcome to buy the famous brands' products in stock at cheap price from us.Discontinuous Rubber Pad quotation
website:http://www.sincholdrail.com/crane-rail-pads/discontinuous-rail-pads/
Product Introduction
SINCHOLD D2 Discontinuous Steel Composite Rail Rubber Pads are designed for installations where rails are mounted on individual sole plates.The rectangular groove of elastic composite rubber pad arranged in the section direction of the direction of the plate.To reduce the overall plate lateral force after deformation and the deformation caused by squeezing rubber surface damage.Because of the steel plate, the structure is very reasonable.After 2 million times of fatigue test is still a good performance. So, even after long time use plate is not damaged.
Product Feature and Application
The composite plate used for bedding under the rail and length along the rail layout. Width is smaller than rail bottom width 4 to 5 mm.The composite plate type structure become two layers of rubber block 0.5-0.7 high quality steel after hot glue composite structure type. Suitable temperature range -20℃-80℃.After the installation after the pressing force of rail plate, the composite plate can keep close contact with rail and rail bottom, make up the rail support surface roughness, in the loaded plate under wheel load will not stretch,instead the grooves are filled,enhance composite plate stiffness, can also prevent the large pressure produced by internal stress of crane, uniform crane wheel pressure, eliminate the fatigue stress produced by the concentrated load.
1.Rubber pads use oil resistant rubber,the performance should conform to GB/T5574-1994 standard 《industrial rubber》
Rubber pads machinery to meet the following requirements:
NameHardness
（Shore A ）Tensile Strength
N/mm²Elongation at Break(%)Pressured Elastic Modulus N/mm²
Composite Rubber PadH7—H8>13>25080~120
2.The bond stress between steel and rubber of composite rubber pad >1 N/mm²
3.Shore Hardness:75°±A 5(DIN53505)
4.Tensile Strength:（ASTMD412C）leave factory 12.5N/mm²^2—aging 10.5N/mm^2
5.Elongation: leave factory 250%—aging 200%
6.Long Deformation（According to BS903 part A6）leave factory less than 5%，aging less than 20%
7.Allowable Compression Stress：80N/mm^2=80MPa
8.Operating Temperature: from -25℃ to100℃
9.Noise and Vibration Reduction:Noise average reduction 10% DBA,vibration average reduction 48%an
Production Details
Deliver,Shipping and Service
Packaging Details:cartons or pallets
Delivery Detail: according to your requirements,accept L/C or T/T payment
If you're going to wholesale the sinchold d2 discontinuous steel composite rail rubber pads made in China, welcome to consult the price list and the quotation with us. We're one of the leading China manufacturers and suppliers, welcome to buy the famous brands' products in stock at cheap price from us.Discontinuous Rubber Pad quotation
website:http://www.sincholdrail.com/crane-rail-pads/discontinuous-rail-pads/